Beiträge von schnikemike

  • Mobiler UMTS / Wlan Router via Bluetooth

    Ist da wirklich so unverständlich?


    Na klar will ich mit Bluetooth in ein Wlan oder sogar Umts netz einwählen. ?????
    Ich komm zar auf ungewöhnliche idee aber ich habe noch nie Versucht mit einem Traktor am Münchner Flughafen eine start und landeerlaubnis zu bekommen!



    Warum habe ich den von einem Mobilen Router gesprochen?


    Also nochmal:


    Ich suche nach einem Mobilen Router (Akkubetrieb) welche Wlandbrige und UMTS kann. Auf diesem soll man sich via Bluetooth einwählen können.


    Ist es jetzt verständlich?

  • Mobiler UMTS / Wlan Router via Bluetooth

    Ich habe noch ein Nokia 9300 Communikator und würde diesen ab und zu gerne nutzen.


    Da das Ding leider nur Bluetooth bzw GPRS kann wäre die Idee mich mittels Bluetooth in ein Wlan bzw Umts Netz über einen mobilen Router einzuwählen.


    Bluetooth ist ja wesendlich schneller als GPRS
    Kennt jemand eine Mobile Lösung?

  • Prepaid+FestnetzFlat+Handy

    ja . endlich habe ich es bemerkt.
    das ich einfach meine debitelkarte mit meine O2 Karte zuhause liegen lasse kann und auf meine Fonic nummer umleite.


    somit hat dann das fonic handz eien o2 genion festnetynummer.
    bzw. man kann das handy ja auch ausschalten und bei nichterreichbarkeit umleiten auf die fonic nummer .

  • UMTS /HSDPA Novatel XU870 unter Linux / Knoppix betreiben / Vodafone einwahl

    Hier ist auch noch eine Lösung die mit allen Linux versionen fnktionieren sollen die den entsprechenden kernel haben.



    Quelle:
    http://www.novatelwireless.com…t/merlin-xu870-linux.html



    Installation Instructions: Linux Setup Guide for the Merlin XU870 HSDPA Modem
    Introduction


    The following describes how to set up the Novatel Wireless Merlin XU870 modem and connect to the Internet on the Linux distribution platform. This description assumes that you have already successfully installed the XU870 Linux drivers.
    Requirements


    Before you can connect to an HSDPA service provider with the Novatel Wireless Merlin XU870 modem, you will need the following:


    * A Novatel Wireless Merlin XU870 ExpressCard™ modem
    * Linux Kernel 2.6 or later (Recommended)
    * A SIM card associated with an active account
    * pppd service installed (pre-installed with a Linux Kernel 2.6 or later)


    Known Limitations


    * You cannot monitor card status such as signal strength, bytes exchanged, or connectivity status. The only network indication available is the wireless card LED that indicates if the card is in a coverage area.
    * No graphical user interface is currently available. All operations are performed using a command line interface.


    Setting Up Your Equipment


    1. Open an xterm window (window A) and log in as root:


    su root
    tail –f /var/log/messages
    2. Insert the XU870 ExpressCard™ modem into your notebook computer.


    Look for the port association and note the lower order port numbers when device is inserted. The information will be used later in this procedure. The following shows sample output:


    Aug 3 15:27:33 linux kernel: usb 5-1: configuration #1 chosen from 1 choice
    Aug 3 15:27:33 linux kernel: airprime 5-1:1.0: airprime converter detected
    Aug 3 15:27:33 linux kernel: usb 5-1: airprime converter now attached to ttyUSB0
    Aug 3 15:27:33 linux kernel: airprime 5-1:1.1: airprime converter detected
    Aug 3 15:27:33 linux kernel: usb 5-1: airprime converter now attached to ttyUSB1
    3. Open another xterm window (window B) and log in as root:


    su root
    cat /dev/ttyUSB0


    There should be additional output displayed in xterm window A that was opened in step 1.
    4. Open another xterm window (window C) and log in as root:


    su root
    5. Unzip the included HSDPA script package:


    unzip hsdpa_scripts.zip
    cd hsdpa_scripts
    cd hsdpa_apn_config
    6. Verify the APN information:


    vi hsdpa_apn_set


    Note: Do not remove the “^M” at the end of the line or open this file in Windows.
    7. After verification, exit the file.
    8. Enter the following:


    cat hsdpa_apn_set > /dev/ttyUSB0
    9. Check the output of the xterm window B opened in step 3 to verify that the APN information is correctly set in the card. The response must match the arguments in the hsdpa_apn_set file and an “OK” response should be in the last line of the window.
    10. Copy the hsdpa_options and hsdpa_chatoptions files to the /etc/ppp directory.
    11. Enter the following to verify that the user and password settings are correct:


    vi /etc/ppp/hsdpa_options
    12. After verification, exit the file.


    Connecting To the Network


    In this section, you will launch a ppp connection to the network.


    1. In your main shell, enter:


    pppd file /etc/ppp/hsdpa_options


    The connection status from the kernel log appears in xterm window A that was opened in step 1 of Setting Up Your Equipment..
    2. To verify that the modem is connected, locate the following line after dialing up (it should be one of the last lines in the log):


    Aug 3 15:53:02 linux pppd[7990]: Script /etc/ppp/ip-up finished (pid 8077), status = 0x0
    3. To confirm that the pppd daemon is associated with the correct ttyUSB port, enter:


    ps –e | grep pppd


    You should see:


    xxxx ttyUSBx 00:00:00 pppd


    ttyUSBx should be the same as that output in step 2 of Setting Up Your Equipment.


    You are now connected to the network.


    Disconnecting From the Network


    1. To hang up the connection, enter:


    killall pppd
    2. Verify the ppp connectivity status using the following command:


    ps –e | grep pppd
    3. Disconnect the session before removing the card from the PC Card slot. Otherwise a system reset may be required to use the card again.


    Troubleshooting


    Dropped connection


    If the connection is lost because you are in a poor coverage area, a manual reconnect is required by repeating the steps in Connecting to the Network.
    DNS problem


    If you experience DNS-related problems, verify the entries in the /etc/resolv.conf file.